Unique Glass Cover Design: Tempered glass upper cover with big 6.25 inch LCD display and touchable buttons, cool look with high transparency, more clear to see real-time data of your inverter
Powerful Inverter: 4000W rated and 8000W peak output. Please check the rated and peak power of your load, add up the watts used by all devices you think you’ll run at the same time and see whether it is within the output power range of the inverter
Stable and Efficient: Pure sine wave output, no interference, extends life of your devices, especially sensitive inductive appliances. Build-in 140A MPPT charge controller, max. PV 5600W 350VDC, max. conversion efficiency 98%
Work without or with Battery: This power inverter can work without battery in daytime, use PV DC current to run the loads. While PV input voltage needs exceed 120V and grid is NOT connected, or it will consumes grid power inevitably. To reduce grid power consumption, we recommend connecting a battery. It works with most kinds of 24V batteries like AGM, Gel, Lead-acid, Lithium-ion and LiFePO4
Hybrid Solar Inverter: This power inverter can configure charging and output priority of solar panels, battery or utility, allowing for energy storage and direct use, provides you sustainable power for off grid life, power outage, emergency
Easy Settings: With function buttons and a LCD display, indicating the operating status and input/output power information, allowing you to set parameters like battery charging current, priority of AC and solar energy
Safe and Reliable: Built-in three cooling fans. Multiple protections for overload, overheat, over current, short circuit. One-key restoration to default settings. Smart battery charge design to optimize battery life
- Before installing and using the solar inverter, it is recommended to install 4 circuit breakers in the following 4 positions:
1. 200A 2-pole breaker between the battery pack and the inverter’s battery input terminals
2. 20A 2-pole breaker between the solar panels and the inverter’s PV input terminals
3. 63A 2-pole breaker between the inverter’s AC power input terminals
4. 40A 2-pole breaker between inverter’s output terminals and load
- This power inverter dose Not support parallel operation.
- This solar inverter is not waterproof. Please install it indoor with good air ventilation or under shelter to protect it from rains.
- The maximum solar input voltage that this 4000 watt inverter can accept is 350VDC. Considering that sometimes the sun is particularly good, the solar input voltage can exceed 350VDC. So it is recommended that the maximum open circuit voltage of the connected solar panel is 280VDC. PV Start-up voltage is recommended to >90Vdc for initial charging the battery.
- This hybrid inverter is featured with a built-in automatic transfer switch (ATS). Connect the utility grid directly to the inverter’s AC input, and connect the inverter’s AC output directly to the load. Do not install any additional transfer switches.
- This solar inverter has only one communication port, for remote mornitoring or BMS. It only supports PACE BMS protocol and the related cable is not supplied. Module for remote mornitoring is sold separately.
Model NameHGX-4KW-120VRated/ Continious Output Power4000 wattsSurge/Peak Power at startup8000 wattsOutput VoltageAC100V-130V SettableOutput Frequncy50Hz/60Hz(Settable)Maxinum PV Array Input5600W, 350VDC, 20APV Start-up Voltage 90VDCPV Array MPPT Volatge Range55-350VDCRecommended PV Input Range90-280VDCAC Input90-140VACMaxinum Charging CurrentSolar 140A, AC 110A, Solar+AC 140ABattery Nominal DC Volatge24VDCBulk Charging Voltage Range24V-29.2VDCFloat Charging Voltage Range24V-29.2VDCLow DC cut-off Voltage Range20V-24VDCOver Charger Protection32VDC
All-in-one Inverter Charger with 140A MPPT Solar Controller
Warm Tips:
4000W Pure Sine Wave Hybrid Solar Inverter for household, outdoor camping, RV, photovoltaic system
Inverter Specifications
Related products
